Murphy EVS-2 Spécifications

00-02-2003 06-21-10 Section 20 The Murphy™ EVS Model EX Electronic Vibration Switch Installation and Operations Manual PHASE OUT / DISCONTINU

Section 20 00-02-2003 06-21-10 - 6 - Mechanical Installation Pre-Installation Requirements Make sure that the surface that you are going to mount t

Section 20 00-02-2003 06-21-10 - 7 - Vertical and Horizontal Installation 1. Make sure you read the bearing or equipment manufacturers instruction

Section 20 00-02-2003 06-21-10 - 8 - Cabling and Wiring Installation Standard EVS S-EX and Analog EVS-A-EX 1. Remove the top cover from the EVS-E

Section 20 00-02-2003 06-21-10 - 9 - 4. Put the power cable through the bottom 3/4” NPT opening. (See Teflon Wrapping Technique at the end of this

Section 20 00-02-2003 06-21-10 - 10 - 7. Connect the relay wires according to the pin out diagrams above. 8. Reconnect the 8-pin connector by pus

Section 20 00-02-2003 06-21-10 - 11 - External Standard Accelerometer Wiring 1. Remove the EVS EX top cover. 2. Connect the Power and Relay wires

Section 20 00-02-2003 06-21-10 - 12 - 6. Reconnect the 3-pin connector by pushing it onto the header until it snaps into place. 7. Thread the con

Section 20 00-02-2003 06-21-10 - 13 - Configuration Setting the Alarm Threshold WARNING! Always adjust the IPS alarm threshold to meet your specif

Section 20 00-02-2003 06-21-10 - 14 - 3. If you are setting your vibration alarm as a function of the baseline (or a multiple of the baseline), fi

Section 20 00-02-2003 06-21-10 - 15 - Setting the Delay Setpoint WARNING! Always adjust the Delay to meet your specific requirements. Too long a

In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications and designs at any t

Section 20 00-02-2003 06-21-10 - 16 - Configuring Latching and Non-Latching/Fail-safe and Normal Modes The alarm relays can be configured to operat

Section 20 00-02-2003 06-21-10 - 17 - The dip switch indicator allows you to select one of four modes by moving the black rectangles to indicate th

Section 20 00-02-2003 06-21-10 - 18 - Specifications Environmental Temperature: -40° and +85°C (-40° and +185°F) Humidity: 0-95% non-condensing V

Section 20 00-02-2003 06-21-10 - 19 - Reset Input Activated by external N.O. relay or push button contact Reset activation time: 0.5 seconds mini

Section 20 00-02-2003 06-21-10 - 20 - 3. Wrap the Teflon tape (3) times around the fitting, hold down on the threads with your thumb, and pull on

Table of Contents Table of Contents ...

(THIS PAGE INTENTIONALLY LEFT BLANK) PHASE OUT / DISCONTINUED Check Availability

Section 20 00-02-2003 06-21-10 - 1 - Product Information EVS Model EX Overview The EVS EX is used for high end vibration protection in a low profil

Section 20 00-02-2003 06-21-10 - 2 - Features Standard switch with on-board sensor, 1.5 ips Adjustable set point range and adjustable time delay fr

Section 20 00-02-2003 06-21-10 - 3 - 4-20mA Output (Analog Option) Accuracy ± 5% of full scale at 1.5 ips, 100Hz, 21° C (69.8°F) 20 mA corresponds

Section 20 00-02-2003 06-21-10 - 4 - Product Dimensions PHASE OUT / DISCONTINUED Check Availability

Section 20 00-02-2003 06-21-10 - 5 - Installation Disassembly and Reassembly Always disconnect the power cord before disassembling. WARNING! Failu